june 2010 doc id 17641 rev 2 1/8 8 BTA06T-600CWRG 6 a snubberless? triac features high static and dynamic commutation bta series is ul1557 certified (file ref.: 81734) package is rohs (2002/95/ec) compliant i gt = 35 ma applications specially designed for power tool applications, it can also be used to drive loads like motor speed controller, kitchen equipments such as electro valves, light dimmers and similar. description available in through-hole package, the triac bta06t-600cw is suitable for general purpose ac switching. being a fully insulated package, the bta06t-600cw provides insulation rated at 2500 v rms. tm : snubberless is a trademar k of stmicroelectronics a2 g a1 a1 a2 g to-220ab insulated bta06t-600cw www.st.com
characteristics BTA06T-600CWRG 2/8 doc id 17641 rev 2 1 characteristics table 1. absolute maximum ratings (limiting values) symbol parameter value unit i t(rms) on-state rms current (full sine wave) t c = 100 c 6 a i tsm non repetitive surge peak on-state current (full cycle sine wave, t j initial = 25 c) f = 60 hz t = 16.7 ms 47 a f = 50 hz t = 20 ms 45 i 2 ti 2 t value for fusing t p = 10 ms 13 a 2 s di/dt critical rate of rise of on-state current i g = 2 x i gt , t r 100 ns f = 120 hz t j = 125 c 50 a/s v dsm /v rsm non repetitive surge peak off-state voiltage t p = 10 ms t j = 25 c v drm /v rrm + 100 v i gm peak gate current t p = 20 s t j = 125 c 4 a p g(av) average gate power dissipation t j = 125 c 1 w t stg t j storage junction temperature range operating junction temperature range -40 to +150 -40 to +125 c table 2. electrical characteristics, snubberless (3 quadrants) (t j = 25 c, unless otherwise specified) symbol test conditions quadrant value unit i gt (1) v d = 12 v r l = 30 i - ii - iii max 35 ma v gt v d = 12 v r l = 30 i - ii - iii max 1.3 v v gd v d = v drm r l = 3.3 k i - ii - iii min 0.2 v i h (2) i t = 100 ma max 35 ma i l i g = 1.2 x i gt i - iii max 50 ma ii 80 dv/dt (2) v d = 67% v drm , gate open, t j = 125 c min 750 v/s (di/dt)c (2) without snubber, t j = 125 c min 8.0 a/ms 1. minimum i gt is guaranteed at 5% of i gt max. 2. for both polarities of a2 pin referenced to a1 pin table 3. static electrical characteristics symbol test conditions value unit v tm (1) i tm = 8.5 a, t p = 380 s t j = 25 c max 1.6 v v to (1) threshold voltage t j = 125 c max 0.85 v r d (1) dynamic resistance t j = 125 c max 80 m i drm i rrm v drm = v rrm t j = 25 c max 5a t j = 125 c 1 ma 1. for both polarities of a2 pin referenced to a1 pin
BTA06T-600CWRG characteristics doc id 17641 rev 2 3/8 table 4. thermal resistances symbol parameter value unit r th(j-c) junction to case (ac) 3.4 c/w r th(j-a) junction to ambient 60 figure 1. maximum power dissipation versus rms on-state current (full cycle) figure 2. on-state current (rms) versus case temperature (full cycle) 0 1 2 3 4 5 6 7 8 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 =180 180 p(w) i t(rms) (a) 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 0 25 50 75 100 125 =180 i t(rms) (a) t c (c) figure 3. on-state current (rms) versus ambient temperature (free air convection) figure 4. relative variation of thermal impedance versus pulse duration 0.0 0.5 1.0 1.5 2.0 2.5 0 25 50 75 100 125 =180 i t(rms) (a) t amb (c) 1.e-03 1.e-02 1.e-01 1.e+00 1.e-03 1.e-02 1.e-01 1.e+00 1.e+01 1.e+02 1.e+03 zth(j-a) zth(j-c) k=[z th / r th ] t p (s) figure 5. relative variation of gate trigger current, and gate trigger voltage versus junction temperature figure 6. relative variation of holding current and latching current versus junction temperature 0.0 0.5 1.0 1.5 2.0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 i gt q1-q2 v gt q1-q2-q3 i gt q3 i gt ,v gt [t j ]/i gt ,v gt [t j =25 c] t j (c) typical values 0.0 0.5 1.0 1.5 2.0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 i h i l i h ,i l [t j ] / i h ,i l [t j =25 c ] t j (c) typical values
characteristics BTA06T-600CWRG 4/8 doc id 17641 rev 2 figure 7. surge peak on-state current versus number of cycles figure 8. non-repetitive surge peak on-state current for sinusoidal 0 5 10 15 20 25 30 35 40 45 50 1 10 100 1000 non repetitive t j initial=25 c one cycle t=20ms repetitive t c =100 c number of cycles i tsm (a) 1 10 100 1000 0.01 0.10 1.00 10.00 t j initial=25 c di/dt limitation: 50 a/s i tsm i2t i tsm (a), i2t (a2s) t p (ms) pulse t < 10 ms, and corresponding value of i t p 2 figure 9. on-state characteristics (maximum values) figure 10. relative variation of critical rate of decrease of main current (di/dt)c versus junction temperature figure 11. relative variation of critical rate of decrease of main current (di/dt)c versus reapplied (dv/dt)c figure 12. relative variation of static dv/dt immunity versus junction temperature 1 10 100 012345 t j =25 c t j =125 c t j max : v to = 0.85 v r d = 80 m v tm (v) i tm ( a ) 0 1 2 3 4 5 6 7 8 25 50 75 100 125 t j (c) (di/dt) c [t j ]/(di/dt) c [t j =125 c] 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 1.0 10.0 100.0 (di/dt) c [(dv/dt) c ] / specified (di/dt) c (dv/dt) c (v/s) typical values 0 1 2 3 4 5 6 7 8 25 50 75 100 125 v d =v r =400 v dv/dt [t j ]/dv/dt[t j =125 c] t j (c)
BTA06T-600CWRG ordering information doc id 17641 rev 2 5/8 2 ordering information figure 13. ordering information scheme bt a 06 t - 600 cw rg triac series insulation specific application voltage packing mode a = insulated 06 = 6 a 600 = 600 v rg = tube current sensitivity and type c = 35 ma, w = snubberless
package information BTA06T-600CWRG 6/8 doc id 17641 rev 2 3 package information epoxy meets ul94, v0 lead-free packages in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. table 5. to-220ab insulated dimensions ref. dimensions millimeters inches min. typ. max. min. typ. max. a 15.20 15.90 0.598 0.625 a1 3.75 0.147 a2 13.00 14.00 0.511 0.551 b 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 c 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 2.40 2.70 0.094 0.106 f 6.20 6.60 0.244 0.259 ?i 3.75 3.85 0.147 0.151 i4 15.80 16.40 16.80 0.622 0.646 0.661 l 2.65 2.95 0.104 0.116 l2 1.14 1.70 0.044 0.066 l3 1.14 1.70 0.044 0.066 m2.60 0.102 c b2 c2 f ? i l a a1 a2 b e b1 i4 l3 l2 c1 m
BTA06T-600CWRG ordering information doc id 17641 rev 2 7/8 4 ordering information 5 revision history table 6. ordering information order code marking package weight base qty packing mode BTA06T-600CWRG bta06t-600cw to-220ab ins 2.3 g 50 tube table 7. document revision history date revision changes 15-nov-2007 1 initial release. 17-jun-2010 2 updated title on page 1 . updated ecopack statement.
BTA06T-600CWRG 8/8 doc id 17641 rev 2 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2010 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
